"mad8" <mad8vskillz@gmail.com> wrote in message
news:1128978932.518662.275030@g47g2000cwa.googlegr oups.com...
> 1) the reg is counter threaded (my ion's reg is)
> when you "tighten" it, the output pressure goes down
>

That would explain why the gauge on my reg goes up accordingly.


> 2) is there an lpr on your cocker? maybe that's set weird?
>

The LPR governs the front pneumatic pressure to the ram, not the air
pressure that launches the ball.

I've read on Otterssccustoms that if I set the input pressure too high, then
the valve won't stay open long enough, though I was setting it at 300psi
based on the micro gauge. May not be accurate enough.

-Bruce

The first thing that springs to mind is that the palmer's stabilizer has a
ramp up/ramp down/ramp up setup. If you turn it out too far, it seems to do
what you're describing. Crank it in(while the velocity drops) and then it
SHOULD go back up again, as you reach the next level of pressure.

The next thing, and this is unlikely, your cocking rod could be coming loose
during firing. Might want to put a spot of loctite on it once you get your
velocity dialed in, and just adjust with the stabilizer.

The most likely version is the step up/down/up thing that Palmers has going
for it. Just screw it in more than you think you should. Eventually it
will either bottom out, or your pressure will increase.

The other thing is this: are you SURE the pressure from the stock reg was
set at 200psi? That sound AWFULLY low for a stock or even modified cocker.
Most cockers have an operating pressure upwards of 400psi at least. I
wouldn't want to be responsible for telling you to massively INCREASE the
pressure(thus blowing every pneumatic device in your gun), but still, it's
something to consider.

--
Jeff Goslin - MCSD - www.goslin.info
It's not a god complex when you're always right


"Bruce Chang" <bechang@swspambegonebell.net> wrote in message
news:%9A2f.233$dO2.75@newssvr29.news.prodigy.net.. .
> So as I've posted previously, I bought a bunch of paintball stuff and
> included in it was a palmer stabilizer that I decided would find it's new
> place to live on my autococker. So I checked the stock reg and found that
> it was set somewhere around 200 psi. Okay.. So I hook up the palmer and
> adjust it's pressure down to around 200psi and air up my cocker and give
it
> a whirl. All in all, everything seems to be okay but the paintball is
> falling off sooner than I think it should, so I'm thinking, I need to turn
> up the velocity a bit. So I didn't mess with the velocity spring,
instead,
> I turned up the input pressure. As I turn up the regulator pressure, the
> velocity drops. I mean, the ball woudln't even reach 20 feet, much less
> 50-100 feet. So I turn the presure back down and velocity increases
again.
>
> I'm not sure what to think though the symptoms I'm getting are kinda
> counter-intuitive. Anyone have any ideas what's going on? Do I have some
> kind of flow problem?
>
> -Bruce
>
>

"Bruce Chang" <bechang@swspambegonebell.net> wrote in message
news:%9A2f.233$dO2.75@newssvr29.news.prodigy.net.. .
> So as I've posted previously, I bought a bunch of paintball stuff and
> included in it was a palmer stabilizer that I decided would find it's new
> place to live on my autococker. So I checked the stock reg and found that
> it was set somewhere around 200 psi. Okay.. So I hook up the palmer and
> adjust it's pressure down to around 200psi and air up my cocker and give
> it a whirl. All in all, everything seems to be okay but the paintball is
> falling off sooner than I think it should, so I'm thinking, I need to turn
> up the velocity a bit. So I didn't mess with the velocity spring,
> instead, I turned up the input pressure. As I turn up the regulator
> pressure, the velocity drops. I mean, the ball woudln't even reach 20
> feet, much less 50-100 feet. So I turn the presure back down and velocity
> increases again.
>
> I'm not sure what to think though the symptoms I'm getting are kinda
> counter-intuitive. Anyone have any ideas what's going on? Do I have some
> kind of flow problem?
>
> -Bruce
you can overpressurize the valve which will make it drop back down.

what you need to do is sweet-spot the reg then adjust the velocity screw
from there.

http://www.cockertech.com/how_sweetspot.shtml

"Jeff Goslin" <autockr@comcast.net> wrote in message
news:QO6dnR5Iob_kc9fenZ2dnUVZ_s6dnZ2d@comcast.com. ..
> The first thing that springs to mind is that the palmer's stabilizer has a
> ramp up/ramp down/ramp up setup. If you turn it out too far, it seems to
do
> what you're describing. Crank it in(while the velocity drops) and then it
> SHOULD go back up again, as you reach the next level of pressure.
>

*Snicker**Snort**Gurgle**Snort, snort*!!

ROTFLMBAO!!

Uhmm, nawww...that ain't it chief.

See the next response....

(ps. that's..."laughing my BIG ass off")